Just Answer Just Answer
Ask A Question  -  Help  -  Register  -  Login   

Ask Your Car Question. Car Experts Answer You ASAP
(Not a Car Question?)

Question

where is the srs control module on a 1997 honda civic


Sent to Car Experts October 08, 2005 9:43 p.m.
No Comment Added
Customer (name blocked for privacy)
Status: Closed   Value: $5   
Answer
October 08, 2005 9:47 p.m. (4 minutes and 11 seconds later) 		ACCEPTED Check Mark

You'll see it in the dash around the center.

Images available only to Customers.



__________________
If I was helpful, please click the ACCEPT
button.

PictureHammer Time  -- L1 Master Technician -- 98% Positive Feedback on 2710 Car Accepts
ASE Mastertech with Adv level Engine performance cert.
Reply to Hammer Time
Sent October 08, 2005 10:05 p.m. (17 minutes and 15 seconds later)
What has to come out to change srs ecu
Customer (name blocked for privacy)
Reply
Sent October 08, 2005 10:19 p.m. (14 minutes and 31 seconds later)
what has to be removed to get to theSrS control module
Customer (name blocked for privacy)
Answer
October 08, 2005 10:19 p.m. (20 seconds later) 		ACCEPTED Check Mark
< cellSpacing=10 cellPadding=0 wid="90%"> <> <>

CAUTION:

  • Before disconnecting any part of the SRS wire harness, disconnect the airbag connector(s).
  • During installation or replacement, do not bump (impact wrench, hammer etc.) the area near the SRS unit.

NOTE:

  • Do not damage the SRS unit terminals or connectors.
  • Do not disassemble the SRS unit; it has no serviceable parts.
  • Store the SRS unit in a clean, dry area.
  • Do not use any SRS unit which has been subjected to water or shows signs of being dropped or improperly handled, such as dents, cracks or deformation.
  1. Disconnect the battery negative cable, then disconnect the positive cable from the battery, and wait at least three minutes.
  2. Disconnect the airbag connector(s): NOTE: When disconnected, the airbag connector is automatically shorted. Driver's Side Remove the access panel from the steering wheel, then disconnect the 2P connector between the driver's airbag and cable reel. Front Passenger's Side Disconnect the 2P connector between the front passenger's airbag and SRS main harness.
  3. Remove the right side cover from the SRS unit.
  4. Remove the left side cover from the SRS unit, then disconnect the SRS main harness 18P connector from the SRS unit.
  5. Remove the four Torx bolts from the SRS unit, then pull out the SRS unit from the driver's side.
  6. Install the new SRS unit. NOTE: Do not reuse a torx bolt that has red threads. Replace the bolt with a new one.

Images available only to Customers.

  1. Connect the SRS main harness 8P connector to the SRS unit; push it into position until it clicks.
  2. Install the SRS unit covers (right and left). Make sure the covers snap together in the middle.
  3. Reconnect the driver's airbag 2P connector to the cable reel 2P connector, then reinstall the access panel on the steering wheel.
  4. Reconnect the front passenger's airbag connector to the SRS main harness.
  5. Reconnect the battery positive cable, then the negative cable.
  6. After installing the SRS unit, confirm proper system operation: Turn the ignition switch ON (II); the SRS indicator light should come on for about six seconds and then go off.
<LINK href="http:///css/onlineApp2.css" type=text/css rel=stylesheet target="_blank">





__________________
If I was helpful, please click the ACCEPT
button.
PictureHammer Time  -- L1 Master Technician -- 98% Positive Feedback on 2710 Car Accepts
ASE Mastertech with Adv level Engine performance cert.
Reply
Sent October 09, 2005 3:43 a.m. (5 hours and 23 minutes later)
do i need any specific tools to remove this part and dose the glove compartment come out?
Customer (name blocked for privacy)
Answer
October 09, 2005 8:16 a.m. (4 hours and 32 minutes later) 		ACCEPTED Check Mark

You will need a set or Torx drivers or sockets.

The glove box does come out but that won't necessarily help you and the instructions don't seem to indicate a need for that.



__________________
If I was helpful, please click the ACCEPT
button.
PictureHammer Time  -- L1 Master Technician -- 98% Positive Feedback on 2710 Car Accepts
ASE Mastertech with Adv level Engine performance cert.

Think you can answer this question?
 Login or  Become an Expert









DISCLAIMER: You acknowledge that any information you may obtain from individuals you contact through use of the Just Answer service comes from those individuals, not from Just Answer!, and that Just Answer is not in any way responsible for any of the information these third parties may supply. The site and services are provided "as is" with no warranty and no representations are made regarding the qualification of an Expert. Responses and comments on Just Answer! are for general information and are not intended to substitute for informed professional advice (such as medical, legal, investment or accounting) and do not establish a professional-client relationship. Just Answer! is not intended or designed to address EMERGENCY QUESTIONS which should be directed immediately by telephone or in-person to qualified professionals. Please carefully read the Terms of Service.
   Just Answer! > Car Repair > For Questions
Question List - Become an Expert - Terms of Service - Security & Privacy - About Us
© 2008 Just Answer Corp.